ZappBots wishes a warm welcome to everyone.

Especially our visitors from
Savage///Circuits and Parallax!!!


Please take a look our new forums, we hope you register and become an active user.

The ZappBots forums are being run on phpBB 3.1.4 software which is different then the vBulletin used on the Savage///Circuits and Parallax forums.
Therefore, things look and work a little different, especially creating posts and uploading images / attachments.


The important thing is we have a place toTalk, Learn and Showcase our projects.

Test equipment question

Open Discussion and Chatter [Non-Topic Discussion]
Please read the Rules & Guidelines post before making any posts on the forums.
Please make your first post a reply to the New Members Introduction post.
User avatar
jknightandkarr
Member
Member
Posts: 179
Joined: Tue May 12, 2015 5:11 pm
Location: Hopelessly lost on the USS-Titanic 968 years from home....
Contact:

Test equipment question

Postby jknightandkarr » Mon Apr 01, 2019 7:11 pm

Question I have an Instek GOS-620 oscilloscope and model 8100a multifunction counter, not on the back of the scope theres a bnc i think its called, jack labled Ch 1 output 20mV/Div into 50ohm, now my question is can this jack be hooked into either of my multifuntion counters bnc jacks to give me the signal thats input on ch 1 of the oscilloscope, and if so, is there a special cable or just 2 bnc connectors with wire between them? Thanks.

Joe
Image
My website- Http://titaniceng.altervista.org/

My Facebookhttps://www.facebook.com/TitanicElectronicsGames/

~Owner, Designer & Builder Killer K.A.R.R.
~Starfleet Captain Joe R.
USS-Titanic Registry Number NCC-1513
Launched: Star Date 48509.9 Galaxy Class, Titanic Sub-Class Starship Max Warp: 15.96

User avatar
zappman
Administrator
Administrator
Posts: 115
Joined: Wed May 06, 2015 12:31 am
Contact:

Re: Test equipment question

Postby zappman » Sat Apr 20, 2019 1:02 am

Looking at the this user manual https://www.gwinstek.com/en-US/products/downloadSeriesDownNew/2601/253, you just need a single coax cable with a BNC connector on each end.
Image
butlh ghajbogh nuv'e' yIHo'.
Admire the person with dirt under his fingernails.

User avatar
jknightandkarr
Member
Member
Posts: 179
Joined: Tue May 12, 2015 5:11 pm
Location: Hopelessly lost on the USS-Titanic 968 years from home....
Contact:

Re: Test equipment question

Postby jknightandkarr » Tue Apr 23, 2019 4:01 am

Cool! That's what I thought I needed, but was't sure. I can probly fine one pretty easy. Better to ask n be sure then not know n damage something. Thanks Zapp!

Joe
Image
My website- Http://titaniceng.altervista.org/

My Facebookhttps://www.facebook.com/TitanicElectronicsGames/

~Owner, Designer & Builder Killer K.A.R.R.
~Starfleet Captain Joe R.
USS-Titanic Registry Number NCC-1513
Launched: Star Date 48509.9 Galaxy Class, Titanic Sub-Class Starship Max Warp: 15.96

User avatar
Savage///Circuits
VIP
VIP
Posts: 357
Joined: Tue May 12, 2015 2:43 pm
Location: Plumas Lake, CA
Contact:

Re: Test equipment question

Postby Savage///Circuits » Fri Oct 02, 2020 1:15 am

How did this work out for you? Typically you'd need to make sure you're impedance matched as well and that your volts/div matched the expected output range.
Image
I'm only responsible for what I say, not what you understand.


Return to “General Discussion”

Who is online

Users browsing this forum: No registered users and 1 guest